Logo

How To Sharpen Ninja Blender Blades – 7 Easy Steps 

Have you noticed that your Ninja blender isn’t performing as fine as it used to? Then there’s a good chance that the blades become blunt and need sharpening. Even the best-quality blades will become dull over time. Fortunately, there are ways How To Sharpen Ninja Blender Blades. It’s easy to sharpen them yourself with the seven simple steps discussed here. Check out these tips to get your blades razor sharp in a few minutes and restore them to their former glory.

Equipment Needed:

To sharpen your ninja blender blades, you will need the following

A Sharpening Stone

An Oil Stone

A File

A Bowl

How to Sharpen Ninja Blender Blades

Step 1: Unplug The Blander From The Power Source

Unplug The Blander From The Power Source is an important task. Do it before starting any cleaning or maintenance tasks. While unplugging, keep in mind that “Safety First.” Keep your hands dry and avoid any electric shock when removing from the power socket. Unplugging will ensure that the device is completely safe to work on. And will also prevent any accidental power surges that could damage the unit.

Step 2: Retouch The Jar From The Base

Detach The Jar From The Base and take off the four screws that secure the base onto the jar. It will allow you to pull off the blade cover, revealing the blades underneath. 

Step 3: Separate The Blades From The Bottom

Once exposed, separate the blades from the bottom using a pair of pliers. It will enable you to reach each blade and sharpen them as needed.

Step 4: Wash The Blades With Great Caution

Put the blades in a bowl and wash them using a soft cloth and warm soapy water. Be very careful in handling the blades as they are quite sharp and may cut your hands. Also, wash them gently to avoid scratching or damaging them while cleaning. It can reduce their effectiveness.

Step 5: Sharpen The Blades With Sharpening Stone

To sharpen the blades, you will need a sharpening stone. Wet the stone and coat it with oil to help keep the blade sharp. Run the blade along the surface of the stone at a 45-degree angle. Make sure you always run the blades from inward to outward direction and not from outward to inwards. Also, be sure to run the blades against the stone, not the stone against the blades. Do this for each blade. Rinse off the blades and check their edges for sharpness after sharpening.

Step 6: Reassemble The Blender Parts

Reassemble The Blades On The Bottom Of The Jar. Once you have reattached the blades to the bottom of the jar, use a screwdriver to secure them in place. Make sure that they are securely fastened and that no gaps exist between them and the base of the jar. Reassemble other parts of the blender like the jar with the base and the lids, etc in their right position. 

Step 7: Test The Sharpness Of The Blades

Plug in the blender and hit the blend button. If everything goes well, you have successfully sharpened your ninja blender blades! If not, go back and re-check your work to see where you may have gone wrong. With a bit of practice, you’ll be able to get those blades razor sharp as good as new ones!

Alternative Ways Of Sharpening The Blades

If you don’t have access to a stone or file, you have alternative ways of sharpening your ninja blender blades. You can use a metal ruler to rub the edges at a 45-degree angle and sharpen them this way. You may use a wooden block wrapped with sandpaper. Both methods will help keep your blades in good condition and ensure they last long. 

10 tips for taking good care of Ninja Blender And the Blades 

1. Always unplug the blender before starting any cleaning or maintenance tasks.

2. Detouch the jar from the base and remove the screws that lock it in place. It will enable you to reach the blades underneath.

3. Separate the blades from the bottom using a pair of pliers. Be very careful not to cut your hands and damage the blades in the process.

4. Sharpen each blade with a stone or file. Ensure to hold the blades at a 45-degree angle and go slow and steady to avoid damaging the edge of the blade.

5. Rinse off blades and check for sharpness with your fingertips after sharpening 

6. Reattach the blades to the bottom of the jar with a screwdriver. Test sharpness by blending a smoothie or juice

7. If everything goes well, you have successfully sharpened your ninja blender blades! If not, go back and re-check your work to see where you may have gone wrong

8 Wash all parts of the blender with warm soapy water and dry thoroughly before reassembling

9 Keep all parts of the blender in a cool, dry place when not in use

10 When traveling with your blender, ensure all parts are fastened and packaged. 

If you take care of your Ninja blender blades, they will last long with high performance. 

Ninja Blender Replacement Blades And PartsList- Blade Assembly

  • Bottom Blade
  • 64 oz. Pitcher
  • 32 oz. Cup
  • Slicing/Shredding Disc
  • 2 Rubber Gaskets

Final Judgment About Sharpening Ninja Blender Blades

Though it may initially seem daunting, taking care of your ninja blender blades is easy. With a few simple tips and some practice, you’ll be able to keep your blades razor-sharp and in top condition. Ensure to unplug the blender before starting any cleaning or maintenance tasks. Detach the jar from the base, and separate the blades from the bottom with a pair of pliers. Sharpen the blades with either a stone or a file. Reattach the blades to the bottom of the jar with a screwdriver. Test sharpness by blending a smoothie or juice. 

FAQ

Q: Do blender blades need sharpening?

A: Yes, blender blades do need sharpening from time to time. If they are not kept sharp, they can start to become dull and ineffective. Following the proper steps can sharpen them yourself in a few minutes.

Q: How do I make my blender blades sharper?

A: Blender blades can be sharpened with a stone or file, holding them at a 45-degree angle. It is also vital to go slow and steady so as not to damage the blade’s edge.

Q: How often should you replace the Ninja blender blade?

A: It would be best if you replaced the blender blades every six to eight months. Or whenever they start to show signs of wear and tear. Replace the blades when sharpening prove inadequate. It can keep your blender running in top condition and extend its life.

Q: What should you do If Your Ninja blender Blades Get impaired?

A: If your ninja blender blades get impaired, you should substitute them immediately. Damaged blades can cause the blender to not function well and may even be unsafe. Always ensure to keep your blades in good condition so that you can always prepare your juice and smoothy fresh and enjoy!

Conclusion About How To Sharpen Ninja Blender Blades

Caring for your Ninja blender blades is essential to ensure you get the most out of your machine. With just a few steps and some care, your blades will stay sharp and effective for years. Hope you will find this article helpful to know how to sharpen ninja blender blades. If you have any questions or comments, please don’t hesitate to write in the comment box below. Thank You For Reading! 

Read More:  Are Ninja Blender Parts Interchangeable?

1 thought on “How To Sharpen Ninja Blender Blades – 7 Easy Steps ”

Leave a Comment